spec no: dsao1025 rev no: v.1a date: jan/09/2015 page: 1 of 8 approved: wynec checked: allen liu drawn: l.q.xie erp: 1101033420 t-1 3/4 (5mm) full color led lamp attention observe precautions for handling electrostatic discharge sensitive devices part number: wp154a4sureqbfzgkw hyper red blue green features z uniform light output. z low power consumption. z long life-solid state reliability. z rohs compliant. description z the hyper red source color devices are made with algainp on gaas s ubstrate light emitting diode. z the blue source color devices are made with ingan light emitting diode. z the green source color devices are made with ingan on sapphire light emitting diode. z electrostatic discharge and power surge could damage the leds. z it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. z all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25(0.01") unless otherwise noted. 3. lead spacing is measured where the leads emerge from the package. 4. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice .
spec no: dsao1025 rev no: v.1a date: jan/09/2015 page: 2 of 8 approved: wynec checked: allen liu drawn: l.q.xie erp: 1101033420 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity/ luminous flux: +/-15%. * luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1.wavelength: +/-1nm. 2.forward voltage: +/-0.1v. 3.wavelength value is traceable to the cie127-2007 compliant national standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. notes: 1. 1/10 duty cycle, 0.1ms pulse width. 2. 2mm below package base. 3. 5mm below package base. part no. dice lens type iv (mcd) [2] @ 20ma v iewing angle [1] min. typ. 2 1/2 wp154a4sureqbfzgkw hyper red (algainp) white diffused 400 1000 60 *120 *250 blue (ingan) 300 500 *300 *500 600 1300 *600 *1300 green (ingan) symbol parameter device typ. max. units test conditions peak peak wavelength hyper red blue green 645 460 515 nm i f =20ma d [1] dominant wavelength hyper red blue green 630 465 525 nm i f =20ma ? 1/2 spectral line half-width hyper red blue green 25 25 35 nm i f =20ma c capacitance hyper red blue green 45 100 45 pf v f =0v;f=1mhz v f [2] forward voltage hyper red blue green 1.9 3.3 3.3 2.5 4 4.1 v i f =20ma i r reverse current hyper red blue green 10 50 50 ua v r =5v parameter hyper red blue green units power dissipation 75 120 102.5 mw dc forward current 30 30 25 ma peak forward current [1] 200 150 150 ma reverse voltage 5 v operating/storage temperature -40c to +85c lead solder temperature [2] 260c for 3 seconds lead solder temperature [3] 260c for 5 seconds
spec no: dsao1025 rev no: v.1a date: jan/09/2015 page: 3 of 8 approved: wynec checked: allen liu drawn: l.q.xie erp: 1101033420 wp154a4sureqbfzgkw hyper red
spec no: dsao1025 rev no: v.1a date: jan/09/2015 page: 4 of 8 approved: wynec checked: allen liu drawn: l.q.xie erp: 1101033420 blue
spec no: dsao1025 rev no: v.1a date: jan/09/2015 page: 5 of 8 approved: wynec checked: allen liu drawn: l.q.xie erp: 1101033420 green
spec no: dsao1025 rev no: v.1a date: jan/09/2015 page: 6 of 8 approved: wynec checked: allen liu drawn: l.q.xie erp: 1101033420 packing & label specifications wp154a4sureqbfzgkw terms and conditions for the usage of this document 1.the information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before product ion usage customer should refer to the latest datasheet for the updated specifications. 3.when using the products referenced in this docu ment, please make sure the product is being operated within the environmental and electrical limit s specified in the datasheet. if customer usage exceeds the specified limits, kingbright w ill not be responsible for any subsequent issues. 4.the information in this document applies to typical usage in consumer electronics applications. if customer's application has special reliabilit y requirements or have life-threatening liabilities, such as automotive or medical usage, please co nsult with kingbright representative for further assistance. 5.the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6.all design applications should refer to kingbr ight application notes available at http://www.kingbrightusa. com/applicationnotes
spec no: dsao1025 rev no: v.1a date: jan/09/2015 page: 7 of 8 approved: wynec checked: allen liu drawn: l.q.xie erp: 1101033420
spec no: dsao1025 rev no: v.1a date: jan/09/2015 page: 8 of 8 approved: wynec checked: allen liu drawn: l.q.xie erp: 1101033420
|
